Dexcom G6

Základní nastavení

  • Follow general CGM hygiene and setting sensor recommendation here.

Obecné tipy pro použití smyčky s G6

  • Recent transmitters are called Firefly. Sensors cannot be restarted without removing the transmitter, which itself cannot be reset, they also do not generate raw data.

  • If you are restarting sensors, ensure you are ready to calibrate and keep an eye on variation.

  • Nastřelení senzoru G6 předem v kombinaci s tovární kalibrací pravděpodobně povede k odchylkám ve výsledcích měření. Jestliže nastřelujete senzor s předstihem, pak jej pravděpodobně v zájmu co nejlepších výsledků bude nutné zkalibrovat.

Read more in the article published by Tim Street at www.diabettech.com.

Používáte-li G6 s aplikací xDrip+

  • If you are using a recent (Firefly) transmitter, preemptive restarts are ignored.

  • If you are using a modded transmitter you do not need to use preemptive restarts.

  • If you are using an old rebatteried transmitter, the safest thing to do is disable preemptive restarts. Though, in this case you will have to use the G6 in non-native mode (which is unadvisable as it disables factory calibration and doesn’t filter noisy readings), or else the sensor will stop after 10 days.

  • Vysílač Dexcom G6 může být připojen současně k přijímači Dexcom (nebo pumpě t:slim) a zároveň k vašemu telefonu.

  • When using xDrip+ as receiver uninstall the Dexcom app first. You cannot connect xDrip+ and Dexcom app with the transmitter at the same time!

  • If you need Clarity and want to profit from xDrip+ alarms use the BYODA with local broadcast to xDrip+. You can also use xDrip+ as a companion app of the official Dexcom app, but you might experience delays in BG readings.

  • If not already set up, download xDrip+ and follow the instructions on xDrip+ settings page.

  • Select xDrip+ in in ConfigBuilder, BG Source.

  • Adjust settings in xDrip+ according to xDrip+ settings page

Pokud chcete použít G6 s vlastní vytvořenou upravenou Dexcom aplikací

BYODA broadcast options

  • Tato aplikace vám umožní používat vysílač Dexcom G6 s libovolným telefonem s Androidem.

  • Uninstall the original Dexcom app or patched Dexcom app if you used one of those previously (do not stop the currently running sensor)

  • Install the downloaded apk

  • Enter sensor code and transmitter serial no. in patched app.

  • In phone settings go to apps > Dexcom G6 > permissions > additional permissions and press ‚Access Dexcom app‘.

  • Po krátkém čase by BYODA měla zachytit signál vysílače.

Settings for AAPS

  • Select ‚Dexcom App (patched)‘ in in ConfigBuilder, BG Source.

  • If you don’t receive any values select any other data source, then re-select ‚Dexcom App (patched)‘ to trigger the demand for permissions to establish the connection between AAPS and BYODA-broadcast.

Nastavení pro xDrip+

  • Jako zdroj dat vyberte ‚640G/Eversense‘.

  • Command ‚start sensor‘ must be performed in xDrip+ in order to receive values. This will not affect your current sensor controlled by Build Your Own Dexcom App.

Poradce při potížích s G6

Dexcom G6 konkrétní řešení problémů

  • Scroll down to Troubleshooting here.

Obecné řešení problémů

General Troubleshooting for CGMs can be found here.

Nový vysílač se spuštěným senzorem

If you happen to change transmitter during a running sensor session you might try to remove the transmitter without damaging the sensor mount. A video can be found here. If you opt for this solution instead, you must be careful to avoid damaging sensor contacts with the strip.